Home > Error Code > Artesian Error Codes

Artesian Error Codes


SN, Sn1, Sn2 Sn3, HL, E1, E3, Prh, HtS, Blinking Lights Hi Limit Sensor Failure. HL = High limit switch tripped. F2 = 4 hours daily filtration F4 = 8 hours daily filtration F6 = 12 hours daily filtration FC = continuous filtration EasyPak C = Celsius CL = Current Time of hot = Overheating, water over 112° F. my review here

One sensor has detected 118° F at heater. Ecn = Spa operating in Economy Mode. We make no representation as to the accuracy or completeness of this data and are not responsible for errors or omissions. No action is necessary.

Hot Tub Error Codes

Spa has shut down. FL1 = Water flow problem, inhibited or pressure switch malfunction. If one of these sensors needs to be replaced BOTH should be replaced at the same time. Heater is deactivated.

  1. Both are secured with black plastic nut around the gray cable.
  2. PSoL = Pressure switch open with low pump.
  3. dry = Inadequate water detected in heater. (Displays on third occurrence of "dr" message).
  4. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.
  5. Shut the spa down, remove the filter and make sure all the jets are open.
  6. The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open.

I wanted to thank you for your time explaining what I needed, as I wasn't 100% sure if what I was ordering was correct. For the complete list of error codes click here. SN = Non functional high temperature sensor. Vita Spa Error Codes If your spa is in fact overheating then it is caused by one of two things, either the temperature sensor is defective or the relays on the circuit board that operate

th2/current temperature = On startup indicates temperature probe problem. Balboa Hot Tub Error Codes drops. Hold = Panel sensors have been pressed too many times in a short period of time. http://www.artesianspas.com/customer/faq.html You can often determine the make of the control system by looking inside the spa's equipment area.

If all these test are checked and they did not solve the error code issues, then it is possible you have a defective hi limit sensor. How To Fix Flo Error Hot Tub SEoP = Sensor open or disconnected. The codes above are all related to flow issues or the pressure switch/flow switch and are the most common error codes. If one of these sensors needs to be replaced BOTH should be replaced at the same time.

Balboa Hot Tub Error Codes

Switch closed while pump is deactivated. http://www.justanswer.com/pool-and-spa/6yr6g-clear-high-limit-hl-error-code-artesian.html Do not enter the spa. Hot Tub Error Codes Sundance Spas ILOC = Interlock failure - possible pump or ozone spike FLO = Pressure switch malfunction or Flow switch malfunction (system specific) Hold = Panel buttons pressed to many times Artesian Spa Error Codes Dream Maker Hot Tubs OH = Overheat 108° F, spa is deactivated.

Entire system is disabled. http://dis-lb.net/error-code/apc-error-codes-f01.php FINAL NOTE: Most spas are equipped with pressure switches and can be found threaded into the stainless steel heater manifold. If water temperature drops 20°F below set temperature, low speed pump and heater activates to bring temperature within 15° of set temperature. Consumer Reviews EasyPak Spa Controls "Very pleased with the ease of installation and all the diagnostic features that other spa packs did not even have. Marquis Spa Error Codes

PSoH = Pressure switch open with high pump. Shut the power down, remove the two wires to the pressure switch/flow switch, find some sort of wire to join the wires, but don't do it yet. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. http://dis-lb.net/error-code/as-400-error-codes.php Do not enter the water.

ICE = Freeze condition. 55°F detected. Hot Tub Error Code Oh If the error code goes away and you are getting the proper voltage then replace the pressure switch/flow switch. Brett Aqualine OH = Temp exceeds 118° F Fr = Freeze condition - temp below 40° F FL = Pressure switch failure EO = Shorted temp sensor E1 = Open temp

Heater is shut down, but other spa functions run normally.

FLO* = Flow Switch (heater is deactivated. Do not use spa when temperature is flashing or the OH message is displayed. I CE2 = Freeze protection. Coast Spa Error Codes Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F.

FLO2 = Closed or shorted flow switch on system startup Pinnacle OH = Temperature has exceeded 110° F SN = Sensor failure FL = Flow/pressure switch stuck in closed position Spa Heater is deactivated. Pictured here is a Balboa® control system used in Belize Spas brand. useful reference For information regarding repairs click here If your spa is not overheating and you are getting the above error codes then a couple of things could be happening.

Other issues that can cause these error codes is debris wrapped around the pump impeller, or one of the valves is not open up all the way. Spa is shut down. Pressure switch is not working. Contact qualified service technician.

Once again these can be caused by a flow issue. Sn2 = Nonfunctional temperature sensor. Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit sensor malfunction Sn3 = OHH = Overheat.

See M7 Sensors here. Browse by Price $0 - $24.99 $25 - $49.99 Over $50 CUSTOMER SERVICE Contact Us Shipping Return Policy Privacy Policy Testimonials MY ACCOUNT View Cart Account Pr = When spa is first actuated, it will go into Priming Mode. Once this is done check ACROSS the heater element post, you should have either 110 volts or 220 volts depending on what voltage is operating the control box. When the water is not flowing it should be OPEN, not CLOSED, if it is closed replace it.

See picture below for reference FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end. OHS = Overheat. If it is hot you have a flow issue, or if it stays hot after the pump is shut off either the pressure switch has stuck close (see FLO error codes FL = Flow.

Error & LCD Window Message Codes: ACC (Applied Computer Controls) CoLd = Temperature in the spa heater housing is below 40° F. OH, OHH, OHS, OHt, HL, HiLi, Sn2, Sn3, tS, Ht, Blinking Lights Temperature Sensor Failure. Contact ACC. Balboa (used by Belize Spas and many other hot tubs) pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F.

OH = High temperature condition, has reached 110°F.