Home > Error Code > Aquapure Error Code 181

Aquapure Error Code 181


Dylan (PoolSupplyWorld) That is very strange that you are receiving both of those error codes simultaneously. The system returned: (22) Invalid argument The remote host or network may be down. Any suggestions? I am also reading 36 VDC at the DC cable. http://dis-lb.net/error-code/aquapure-error-code-180.php

If there is buildup or no apparent issues then proceed to step 2. 2) Clean cell in a mixture 4 parts water and 1 part acid, rinse with fresh water when Thanks! Thank you for your help! Share this post Link to post Share on other sites qwester 0 Newbie Members 0 6 posts Posted June 23, 2010 · Report post john_harvey I just went through this

Aquapure Error Code 145

And at the least give Jandy (Zodiac) a phone call to run through any troubleshooting over the phone. Posts 1 AquaPure 1400 Error Codes 172 181 My Aquapure 1400 (4th summer) has service codes 172,181. http://PoolSupplyWorld.com/ Robby Stahl (PoolSupplyWorld) Hello Todd, Yes it is possible that the flow sensor is an issue as well. Dumb question, but are you sure you have water flow?

  1. My ritual has been: I depress the salinity button 3 times then the temp button then increase the salt reading from 2.1 to 3.3 and then increase the chlorine level and
  2. These are troubleshooting options taken directly from Jandy's owners manual and are what the techs use from Jandy as well.
  3. here is how i have it wired: Black(Wall) to Black(Unit) Red(Wall) to yellow/black(Unit) black/red(unit) to black/white(Unit) How do I rewire for the 120 Reply With Quote 08-15-2011,08:20 PM #9 Gusmanb
  4. Thanks in advance for any suggestions.

I do know there is a protective mechanism built into the logic for the generator when salt is too high. Thank you for your help.ChlorinelessinMurrieta Submitted: 4 years ago. The panel that looked like a transparent window actually registered error codes. Aquapure Error Code 125 194 I was out of town for a couple of weeks and returned to a pool full of algae and the Aquapure display indicating Error code 172 and 186.

Lol Gary Gindt I am getting error code 194 Any possible fixes? Salinity is 3.2, and I have the production set to 100% but not enuf chlorine in the pool to kill the green growing. I see no deference there so i am sure both of them are good. http://www.poolsupplyworld.com/blog/jandy-aquapure-troubleshooting-error-codes/ Thanks for any advise!

It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult. Jandy Aquapure 170 Error Code Anybody have any explanation? Jim Mc I have a Jandy Aquapure 1400 sat system about 7 years old. Dylan (PoolSupplyWorld) Hi Paul, Sorry to hear you have been experiencing some issues with your cell.

Aquapure Error Code 121

The salt system does require in the range of 15-20 GPM to operate properly. http://www.poolforum.com/pf2/showthread.php/13882-AquaPure-1400-Error-Codes-172-181 All rights reserved. Aquapure Error Code 145 What does check the DC cord mean? Aquapure Error Code 120 I did clean the sensor with a brillo pad and the codes re-appeared.

Here are a few steps to re calibrate the salinity: •Press the “Salinity”button and hold it until it beeps 3 times. http://dis-lb.net/error-code/aquapure-error-code-144.php The codes flashing are: 172 and 181 . I have cleaned everything and now want to make sure the codes are reset to see if I fixed it. It can be tested inside the box as well at the cell test point to see if the board is outputting voltage to the cellpoolguy810 : to test the voltage to Jandy Aquapure Error Code 120

Reduce water temperature 175 Flow sensor air lock condition or very low salinity Verify proper flow/temperature/salinity sensor installation. PoolDoc / Ben Get the testkits you needBest Guess Chlorine Chart* PoolForum Amazon store *Edit your signatureSubscribe to the ForumBBB Method of Pool CareFixing Cloudy Pool WaterUsing muriatic acid to lower What is flow sensor air lock and how do I correct? navigate to this website Thoughts?

Hayward 1.5 superpump, Autopilot Pool Pilot Digital SWG, Hayward Model S244T 300lb sand filter, TF100 kit Reply With Quote 08-15-2011,08:15 PM #8 Gusmanb View Profile View Forum Posts View Articles Jandy Aquapure Service Codes Fiddlerman Thanks 🙂 Shawn I am not getting any code it says wait, either to much pressure and then it goes down to low pressure is the pump going out? You can't have 120-240VAC.

PoolSupplyWorld Hi Scott, It is possible the cell is damaged.

Hate to be the first in this type of failure. Usually when I get stumped like this I call an expert at the manufacturer, but they seemed to think there is something more going on. There have been lighting strikes nearby, so could it have been a power surge? Jandy Aquapure Service Codes 172 185 I checked the return line chlorine and it registers zero ppm.

Reply With Quote 08-15-2011,08:07 PM #6 jsw5620 View Profile View Forum Posts View Articles Join Date Mar 2011 Posts 135 Re: NEW Jandy Aqua Pure 1400 geting Codes 181, 172,Service How old is the cell? - Christian Wayne Coates I have a 1400 and this year had to replace my chlorine sensor as our dog ate off the wires. Share this post Link to post Share on other sites Pool Clown 0 Spa Guru Members 0 2,685 posts Gender:Male Location:Silicon Valley, CA Gender:Male Posted June 24, 2010 · Report my review here KIm I have a 4 year old Auqua pure system and got the code 125 and 194.

Congrats... You're the first that I've heard, having a sensor fail with the new t-cell. The cell is working. did you have the same problem as well?

The water then exits out of the port where the terminals are closest to.