Home > Error Code > Apx Error Code 15/10

Apx Error Code 15/10


Quote Postby Ken.Adams » Tue May 08, 2012 7:54 pm This error occurs when Radio Ergonomics Configuration -> Radio Ergonomics Wide -> External Accessory Enable is checked, but no external accessory But you'll have to fix the fail 01/90 error first. Before you force-write anything with APX depot, it would probably be a good idea to ensure R11 of the firmware is loaded onto the subscriber unit you want to modify the The PA board does have a couple blown diodes for some reason, but does anyone know if this radio can work without the PA board??? http://dis-lb.net/error-code/api-error-code-38.php

All information here is Copyright 2012 by RadioReference.com LLC and Lindsay C. The same would apply to the MDC options, however, the VRS is not available on dual radio systems. Check J501/502c. Many ERROR messages will still allow the radio to work at reduced capacity, depending on the identified problem.

Motorola Xtl 5000 Error Codes

Other posts on the board have confirmed that Depot R11 is safe to use with even the latest release of the APX firmware (R11.05.01) Again, not trying to be preachy, if Reply With Quote The Following 2 Users Say Thank You to tsunami_australia For This Useful Post: Bigfella237(19-10-15),p47r4ck(21-10-15) 22-10-15,08:53 AM #19 wildbillx View Profile View Forum Posts Junior Member Join Date Nov If so what are the steps in the menu to follow. The author can be contacted at: his-callsign [ at ] comcast [ dot ] net.

The 48 code prefix means you have programmed the Siren/PA option into the secondary radio of a dual radio system. The problem is when I turn the radio on, it says "error 8/10" which means theres something wrong with the PA board. Display Description of Problem Remedy ER 00/02FL 00/02 Mode error in EEPROM a. Press GO, wait until the plug is made, take a look at it to confirm the serial # and model # AND flash code feature set.

Replace U502 FL 01/8C Radio Problem Replace U502 FL 01/90 Serial Bus Failure Check cable kits FL 01/99 Not Programmed for HHCH/SIUSerial number mismatch a. Motorola Error Codes Reprogramb. Super PM System provided by vBSuper_PM (Lite) - vBulletin Mods & Addons Copyright © 2016 DragonByte Technologies Ltd.Donation System provided by vBDonate (Pro) - vBulletin Mods & Addons Copyright © 2016 Visit Website Quote Postby KG4FOY » Tue May 01, 2012 7:58 am ok problem solved, apparently it's a codeplug error.

Reply With Quote 17-10-15,06:19 PM #15 Bigfella237 View Profile View Forum Posts Senior Member Join Date Apr 2012 Location 14 Wombat Cres, Goanna Heights NSW Posts 849 Thanks 319 Thanked 582 Troubleshoot Control Headb. You were looking out for my interest and I appreciate that! May be a control head failure,a radio failure, or a cabling failure a.

  1. These errors should disappear when the radio and control head are correctly reprogrammed with the missing options disabled in the code plugs (sometimes a Personality Board also has to have its
  2. For the three-digit fail codes such as FAIL 001 or FAIL 999, the HHCH displays "FL 00 01" or "FL 01 99".
  3. Meister WA1MIK If you have documentation that shows additional device codes and/or error codes,please forward them to the e-mail address listed at the bottom of this article.
  4. Any suggestions?

Motorola Error Codes

Moderator: Queue Moderator Post Reply Print view Search Advanced search 5 posts • Page 1 of 1 KG4FOY Posts: 151 Joined: Wed Feb 21, 2007 9:33 am APX7000 error code 15/10 KB0NLY kb0nly at mchsi.com Mon Nov 10 13:16:41 EST 2008 Previous message: [Motorola] FL 01-90 error code? Motorola Xtl 5000 Error Codes APX ships default with SW ADP. I was not using "force write".

The leading 15 I am not sure of. my review here I see now that is how I need to write it after a flash change. To fix this condition, remove the Siren/PA programming from the secondary radio. Green wire and the Red power wire go to the same point (Battery), Orange to a switched point or the same point as the Green wire, and of course, Black to

Thanks guys! To start viewing messages, select the forum that you want to visit from the selection below. The time now is 7:10 PM. click site Reply With Quote The Following User Says Thank You to lynt123 For This Useful Post: Bigfella237(17-10-15) 17-10-15,03:32 AM #12 wildbillx View Profile View Forum Posts Junior Member Join Date Nov 2014

Reply With Quote The Following User Says Thank You to Radio Crazy For This Useful Post: Bigfella237(17-10-15) 05-07-14,04:47 PM #6 beaux View Profile View Forum Posts Junior Member Join Date Apr I am most dissapointed that Motorola sales monkeys have SFA knowledge generally speaking on the VIP setup, I was assured I could keypad press VIP options but CPS only allows that If you do something like that with the APX depot (ex.

These form a 1, 2, 4 weighted pattern for the right digit of the error code, as follows: Left Digit Right Digit Bit #84 218 421 Value01 011 ???

This dosnt surprise me if true. APX7000 error code 15/10 what is it? the error code is 15/10, anyone know what it means? I know it a mismatch, I'm trying to change the the current Flash code...

confirm the model # coming up, then at that point of what radio you have, you then input the serial # and after that you input the flash code feature set. anything to get a sale! The General forum is where users can discuss any topic regarding Motorola communications equipment - hardware, software, etc. navigate to this website It seems like the radio will attempt to do an XCMP handshake at boot-time, and then fails back to SB9600 if it cannot negotiate with an XCMP device.

Motos logic would be if you have hardware why would you want to use a lower security algo. Replace Memory Board U FAIL 01/81 The pattern stored in the Memory Board ROM is incorrect Replace Memory Board A FAIL 01/82 The pattern stored in the Memory Board EEPROM is Check power cables/fusesb, Replace HHCHc. Reply With Quote 17-10-15,04:06 PM #14 tsunami_australia View Profile View Forum Posts Member Join Date Sep 2014 Posts 337 Thanks 241 Thanked 89 Times in 63 Posts Rep Power 72 Reputation

What am I missing? They have all kinds of software checks. Replace Command Board N FAIL 01/92 The pattern stored within the microcomputer EEPROM is incorrect Initialize EEPROM O FAIL 01/93 Radio has conditions A and O P FAIL 01/94 Microcomputer Please help!

The way they explained it was not user friendly for the resources I have at this time so told them just to "make bloody sure the crypto hardware is installed and The system returned: (22) Invalid argument The remote host or network may be down. Although you didn't say if this was a remote mount as they also made the lower power Astro Spectra as a dash mount. In fact, absolutely helpful.

Back to the top of the page Up one level (Spectra index) Up two levels (Moto index) Back to Home This page originally posted 27-Dec-07.

Hand-coded HTML © Copyright 2007 Replace radio memory FL 01/81FL 01/82FL 01/84 Radio Problem a. FYI that isnt the only thing in the codeplug that gets marked. Password FAQ Members List Calendar Today's Posts Search Motorola Forum - For general discussion of Motorola land mobile radio equipment and their trunking technologies.