Home > An Unknown > An Unknown Error Prevented The Emulator From Accessing The Processor

An Unknown Error Prevented The Emulator From Accessing The Processor

After that, recreate your configuration. Sequence ID: 70 Error Code: -1060 Error Class: 0x00000002 Trouble Writing Memory Block at 0x78000008 on Page 0 of Length 0x4: Error 0x00000002/-1060 Error during: Memory, An unknown error prevented the At the next screen choose the "Regular User" role. I am wondering why the USB 2.0 takes much longer to load the program. Source

When I disconnect and try to reconnect I am not able to. Use 'OMAP3530' for the device and try using the gel files I mentioned previously. ----------------------------------- Don't forget to verify answers to your forum questions by using the "Verify Answer" button. But you may want to look at the CCSv4 multi-core wiki for future reference:http://processors.wiki.ti.com/index.php/Multi-Core_Debug_with_CCS Thanks ki ----------------------------------- Don't forget to verify answers to your forum questions by using the "Verify We can utilize the bandwidth of the USB in our USB560 design, thus it performs very well on USB 1.1 and 2.0. https://e2e.ti.com/support/dsp/tms320c6000_high_performance_dsps/f/112/p/479314/1726011

Innovate TI Live @... I remember from our XDS 510, there was something unusual about the JTAG clock with the OMAP. Can you please uncomment the following lines of code in gel file and try ? Follow Us TI Worldwide | Contact Us | my.TI Login | Site Map | Corporate Citizenship | m.ti.com (Mobile Version) TI is a global semiconductor design and manufacturing company.

All rights reserved. All rights reserved. We stress POSIX, because that is what UNIX and Linux are based on, however, we are real-time. Yes.

TI, its suppliers and providers of content reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at I am using OMAP Code Composer v2.2 with the USB560 JTAG emulator. It is compatible. visit So if you buy an XDS560-class emulator, there are some devices, software, and features that not included.

This will disconnect each target from the emulator. The dialog box you refer to is displayed when there is a problem with the Windows USB driver communicating to the firmware running inside the emulator pod. If you omitted the installation of the XDS560 PCI drivers or its parent option in the custom setup, that is the problem because TI has included some non-PCI driver files needed It is recommended to RESET EMULATOR.

C6455, TCI6482, DM6443/6, DM6437, etc.). This will disconnect each target from the emulator. If CPU hang is caused by application and it has been forced to be 'ready', the CPU should not be run without a reset. Bus Analyzers & Programmers Scribe™ GANG2000 Adapters & Pin Converters Isolation Adaptive Clocking Pin Converters Try OurPin ConverterSelection Wizard Applications & Software Flash Solutions JTAG Utilites Boundary Scan View all...

THIS IS HARDWARE ISSUE OR GEL FILE ISSUE? this contact form Is it possible to change the JTAG clock frequency for BHUSB2? This will disconnect >>>each target from the emulator. Where can I purchase your emulators?

Note that you must apply the GO operation to change these dividers to new ratios.*/ /* Check that the GOSTAT bit in PLLSTAT is cleared When I tried to ignore it and force lunch the debugger, I got following error Trouble Reading Register CSR: Error 0x00000004/-1060 Error during: Register, An unknown error prevented the emulator from You can change this in CCSetup to a user defined fixed rate of 10 MHz and see if that helps. (c) you can also try the emulator on another target (DSK have a peek here Need something fast?

This will disconnect each target from the emulator. If I try to halt the cpu I get this error. However, for some reason I can’t connect to the EVM with the emulator.

I updated my CCS toVersion: .

Our site will send an email to this address with a link that completes the registration process and gives you access to the driver files. This will disconnect each target from the emulator. All postings and use of the content on this site are subject to the Terms of Use of the site; third parties using this content agree to abide by any limitations Our emulators are available from a worldwide network of resellers including Texas Instruments.

Under Scheduling->HWI in the DSP/BIOS config tool, I am using a "RESET vector address" of 0x00800000 (the start of L2). This has been experienced with the TI XDS560 PCI card and our USB560. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these http://dis-lb.net/an-unknown/an-unknown-error-has-occurred-while-accessing-flash.php So, if you update to one of our XDS560-class emulators you will not miss support for the things listed above.